load point
英 [ləʊd pɔɪnt]
美 [loʊd pɔɪnt]
网络 载入点; 加载点; 负载点; 载荷点; 装入点
双语例句
- Based on large quantity of Brazilian tension tests and uniaxial compression tests, the ratio of elastic modulus to splitting modulus of the Three Gorges granite is estimated as 19.2. Finally, the proportional relationship between load and displacement of load point is numerically simulated by 3D FEM.
定义了劈裂模量，经过大量的劈裂抗拉和单轴抗压对比试验，提出三峡花岗岩的弹性模量与劈裂模量二者的经验比值为19.2。 - After getting load point location information, the ratio of vector-mode can be used to determine the amplitude of load.
得到荷载点位置信息后，利用两个向量的模的比例关系来确定荷载的大小。 - Finally, the paper studies the implementation of the control and monitor system based on Work Load Point system through one concrete pipeline erection sub-project.
最后，本文运用基于工作负荷点系统的进度度量监控体系对一个具体的管道铺设项目进行研究。 - According to the radial structure of oil field distribution network, an associated matrix to describing this network is proposed and solved based on Hopfield neural network, and then the total compensating capacity and the compensation scheme for each load point is obtained.
根据油田配电网呈辐射状的特点，提出了该配电网的关联矩阵，并基于Hopfield神经网络进行求解，得到了无功补偿的总容量和各负荷点的补偿方案。 - By Brazilian tension tests of complete procedure for Three Gorges granite conducted by a servo-controlled testing machine, it is found that there exists obvious linear relationship between load and displacement of load point before breakage.
采用三峡花岗岩在伺服试验机上进行了劈裂拉伸全过程试验，发现试样破坏前加载力与加载点位移存在着明显的线性关系。 - The principle of extension short-time load forecast was put forward, that is forecasting unknown load point by adding information of new load point to the point, the load was known.
提出了扩展短期负荷预测的原理，即在已知当日部分负荷的条件下，引入最新获得的负荷相关信息，预测当日未知的多点负荷。 - It finds out the minimal path for each load, considers the different contributions of the elements on the path and out of the path to the reliability of the load point.
该算法先求各负荷点的最小路，再分别考虑最小路上的元件和非最小路上的元件对负荷点可靠性的贡献。 - The yield load point and maximun load point on the curve can be used to represent abradability, binding strength between coating and matrix.
曲线上的屈服点和最大点综合表征了封严涂层的可磨耗性和涂层与基体的结合强度曲线所包围的面积为冲击刮削韧性，用它可表征涂层的抗冲蚀性。 - The concept, composition and assessing method of the Work Load Point system are defined clearly, and the differences between Work Load Point system and traditional hour-working system are described.
对工作负荷点系统的概念、构成以及评估等进行了清晰的定义，论述了工作负荷点与传统的工时定额之间的区别。 - In this paper, the boundary integral equations are proposed, in which the field point and the load point are separate.
本文推导了场点与载荷点分离时的边界积分方程。